![]() ![]() Void CheckBrightnessSetting1() //Checks the brightness setting j and is used to update the app when the slider changes brightness and when app disconnects and reconnects it updates the app Void ChangeLEDColour() //This changes the colour of the whole stripīyte BrightnessSlider1=0 //Blynk slider widget used to select the brightness setting of LED strip 1īyte BrightnessSlider2=0 //Blynk slider widget used to select the brightness setting of LED strip 2īyte ConfigureBrightnessDisplay1=0 //Controls the updating of the brightness display widget 1 so blynk app is not floodedīyte ConfigureBrightnessDisplay2=0 //Controls the updating of the brightness display widget 1 so blynk app is not floodedīyte AppReconnected=0 //Controls when the reconnection subroutine should start occuring from Void ChangeLEDColour2() //Subroutine responsible for changing the RGB LED strip2 colour Void ChangeLEDColour1() //Subroutine responsible for changing the RGB LED strip1 colour Here’s my variable declaration, setup and loop programming code: //#define BLYNK_PRINT Serialīyte counter1=0 //Used to control the execution of the brightness display on the app and LED bar graphīyte RGBColourReset=0 //Used to control the execution of normalising the LED coloursīyte r1=255,g1=255,b1=255 //Stores RGB command from Blynk app and writes it to the LED strip1īyte r2=255,g2=255,b2=255 //Stores RGB command from Blynk app and writes it to the LED strip2 Strange thing is that the “Blink” example code on github, here., which uses the same line of code, compiles successfully Is actually this line in my program FastLED.addLeds(leds, NUM_LEDS) The line being referred to by C:\Users\Hp Zbook 15\Desktop\Light Control Project\BedSideLightControlExampleV1_7_AddingWS2812LEDControl\BedSideLightControlExampleV1_7_AddingWS2812LEDControl.ino:201:56: required from here Multiple libraries were found for "WiFi.h"Įrror compiling for board ESP32 Dev Module. Multiple libraries were found for "FastLED.h" Multiple libraries were found for "LedControl.h" ![]() Multiple libraries were found for "BlynkSimpleEsp32.h" Static_assert(validpin(), "Invalid pin specified") In file included from C:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/FastLED.h:48:0,Ĭ:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/fastpin.h: In instantiation of 'class FastPin':Ĭ:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/platforms/esp/32/clockless_rmt_esp32.h:178:23: required from 'class ClocklessController'Ĭ:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/chipsets.h:582:7: required from 'class WS2812Controller800Khz'Ĭ:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/FastLED.h:103:52: required from 'class WS2812'Ĭ:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/FastLED.h:302:39: required from 'static CLEDController& CFastLED::addLeds(CRGB*, int, int) 'Ĭ:\Users\Hp Zbook 15\Desktop\Light Control Project\BedSideLightControlExampleV1_7_AddingWS2812LEDControl\BedSideLightControlExampleV1_7_AddingWS2812LEDControl.ino:201:56: required from hereĬ:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/fastpin.h:207:2: error: static assertion failed: Invalid pin specified All SPI access will default to bitbanged output" # pragma message "No hardware SPI pins defined. All SPI access will default to bitbanged output In file included from C:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/FastLED.h:65:0,įrom C:\Users\Hp Zbook 15\Desktop\Light Control Project\BedSideLightControlExampleV1_7_AddingWS2812LEDControl\BedSideLightControlExampleV1_7_AddingWS2812LEDControl.ino:25:Ĭ:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/fastspi.h:130:23: note: #pragma message: No hardware SPI pins defined. # pragma message "FastLED version 3.003.002" This is the error message that is produced: In file included from C:\Users\Hp Zbook 15\Desktop\Light Control Project\BedSideLightControlExampleV1_7_AddingWS2812LEDControl\BedSideLightControlExampleV1_7_AddingWS2812LEDControl.ino:25:0:Ĭ:\Users\Hp Zbook 15\Documents\Arduino\libraries\FastLED/FastLED.h:14:21: note: #pragma message: FastLED version 3.003.002 My program compiles and runs on the Mega but does not compile for the ESP32. I am stuck at the moment trying to get my code to compile for the ESP32 board that I am transitioning to from the Arduino Mega. But since you have experience with the ESP range of controllers and already have seen what I am trying to achieve, I would like some advice and assistance. First let me apologize because what I am about to ask is not a Blynk related issue.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |